Paint on the galvanized layer, the bonding force between each other has a great relationship with the baking temperature of the paint, and alkyd paint is coated after galvanized, and the adhesion is not a problem. After galvanized to do amino paint, paint adhesion is not very good. Do two bottom two surface, adhesion is good, if the two bottom two surface changed to two bottom three surface, that is, more paint, more baked once, again test adhesion is very bad, bad enough to tear the paint from the galvanized layer.
Bridge protection system generally do not need to be specially installed special drainage system, the use of hexagonal mesh made of gabion mesh box, the inside of the filler are selected stones, these stones are not easy to wear, and between the stones and stones will retain some gaps, so it is very good to meet the drainage requirements.
Galvanized hexagonal mesh features: easy to use; Save transportation costs. It can be reduced into small rolls, and involved in moisture-proof paper packaging, occupying little space. Coating thickness uniformity, corrosion resistance is stronger; Simple construction, no special technology; Strong resistance to natural damage and corrosion resistance and the ability to resist adverse climate impact; Can withstand a wide range of deformation and still not collapse. Play the role of fixed heat preservation and insulation.
Galvanizing can be done by zincate galvanizing or chloride galvanizing. Appropriate additives shall be used to obtain a coating that meets the requirements of this standard. Luminescence treatment should be carried out after luminescence plating. The parts that need to be dehydrogenated for passivation should be passivated after dehydrogenation. Before passivation, 1%H2SO4 or 1% hydrochloric acid should be applied to activate 5~15s. Passivation shall be treated with colored chromate unless otherwise specified in the design drawings.
3. Zinc layer structure: The structure of zinc layer includes grain size, grain shape and the combination of zinc layer and substrate, etc., which has a certain impact on corrosion resistance. In general, the finer the grain size, the denser the structure, and the better the corrosion resistance.
The main reason for the high price of stainless steel barbed wire is that the raw material used in the barbed wire is more expensive, because the nickel in it makes it corrosion resistant and ductile. Stainless STEEL BARBED ROPE IS a new type of protective products, precisely because of its corrosion resistance in coastal or often acid rain landing site is widely used, the service life of up to 15 years.
The use of bundled galvanized wire with the development of industry and agriculture also expanded accordingly. Therefore, galvanized wire products in the industry, such as chemical equipment, oil processing, Marine exploration, transport, electricity, shipbuilding, metal structure, etc.), agriculture (such as sprinkler irrigation, dim room, building (such as water and gas transport, wire casing, scaffolding, house, etc.), Bridges, shipping, etc., has been widely use in recent years. Because galvanized wire goods have beautiful surface, good corrosion resistance and other characteristics, its use scale is more and more extensive.
The main raw materials of blade barbed wire are galvanized wire and galvanized sheet. Because the price of galvanized sheet is more expensive than galvanized wire, it is directly reflected in the price of blade barbed wire. There is also the difference in processing technology also leads to the difference in the price of the blade. The traditional barbed rope is made of mechanical wringing, which has a relatively small amount of labor and high production efficiency. However, the blade barbed rope is processed manually after secondary mechanical processing. So whether from the labor force or from the production efficiency also said that there is a large gap. These factors lead to the price of the blade barbed rope is more expensive.
1, stress relief before plating where the maximum tensile strength is greater than 1034Mpa key and important parts before plating should be at 200±10℃ stress relief for more than 1 hours, carburizing or surface quenching parts should be at 140±10℃ stress relief for more than 5 hours.
In the process of production, the acid activation solution can remove the corrosion products and oxide film on the surface of low carbon steel wire without excessive corrosion on the matrix. Galvanized wire can be used zincate galvanized or chloride galvanized process, appropriate additives should be used to obtain the coating required by the standards of low carbon steel wire. When galvanized wire out of the light plating should be carried out light treatment. The bath temperature of galvanized wire should be controlled well.
Twisting hexagon mesh production factory is the selection of low carbon steel silk woven, mesh structure he has corrosion resistance, high strength and ductility and so on. The diameter of steel wire can reach 2.0mm-4.0mm. The surface of steel wire is usually used for hot-dip galvanized maintenance. The thickness of galvanized maintenance layer can be made according to the needs of customers. We have to carefully choose a good cage for the parrot, so that it has a comfortable home.No matter how big they are, dogs seem to love touching noses with people and other animals. In fact, nose touching is a form of social interaction for dogs, much like shaking hands and hugging humans. But dogs don’t rub their noses with every person or animal. They choose who to rub their noses with. If they don’t like you or don’t know you at all, they won’t touch your nose. However, adult dogs will touch the nose of almost every puppy. They will not only touch the puppy’s nose, but also smell the puppy.
In strict accordance with the multi-pass small compression rate drawing, the total compression rate is 96.48%, reducing the scraping of zinc layer. The whole wire drawing die is made of tungsten steel die and polycrystalline die. The Angle of the working cone of the wire drawing die is 12° ~ 16°, and the length of the sizing belt is 0.15 of the diameter of the wire, so as to ensure that the deformation of the zinc layer is basically synchronous with the steel wire substrate.