heated blanket throw sale
-
\text{Energy (kWh)} = \frac{100}{1000} \times 8 = 0.8 \text{ kWh}
...
...
For mountainous or hilly areas where the ground is more undulating set up stakes. You need to set a stake at the beginning and the end, and then determine the position. In the middle of the ups and downs, to increase the stakes according to the complexity of the ups and downs of the terrain, we need to be able to see 3 stakes at the same time, so that the installation is. It’s a straight line.
But there are some necessary precautions in the production of galvanized wire. Remove all tools and piles on the work site and equipment that hinder activities, and slowly put the wire into the cylinder during pickling to prevent acid splashing on the body. When adding acid, the acid must be slowly poured into the water. Do not pour water into the acid to prevent acid spillage and injury. Workers should wear protective glasses when working. Then in the handling of wire and other items, it is strictly prohibited to push hard.And high quality data and production cost and production conditions are bound, so some welding screen manufacturers did not meet the requirements of this aspect, natural in this case there is no way to improve product strength. In addition to data, and produce process, even if again good data, but the factory did not meet the requirements of production process in welding, also can form the product under the high pressure welding, so it is also a kind of strength on the decline, process conditions of different manufacturers also have very big difference, so it formed a shopping mall on the above products are differences of strength.
Thus, when zinc is sufficient in a solid melt, the two atoms of zinc and iron disperse with each other. The zinc atoms in the iron matrix are moved into the lattice of the matrix, and the iron elements are gradually formed into alloys. The zinc composition of iron and intermetallic compound FeZn13 in molten zinc solution and the bottom of hot galvanized sheet can be used as zinc slag. The pure zinc layer composed of zinc leaching solution is hexagonal crystal.
Good galvanized wire, plating thickness of 3- 4 mm, zinc adhesion should be less than 460 grams/m, that is, the average thickness of zinc layer is not less than 65 microns. When the thickness of plated parts is greater than 4 mm, the zinc adhesion should not be less than 610 g/m, that is, the average thickness of zinc layer should not be less than 86 microns. Standard galvanized wire coating must be uniform, galvanized layer basically uniform with copper sulfate solution test etching five times no dew iron. For standard galvanized wire coating adhesion requirements, the zinc layer of plated parts should be firmly combined with the basic metal and have enough adhesion strength, after hammer test does not fall off, not convex.
Two is to pay attention to the storage and use of galvanized wire products, according to the actual environmental standards to choose different specifications of galvanized wire products;
Electric galvanized wire is dipped in the zinc solution of heating ablation, the production speed is fast, the coating is thick but not uniform, the market allows a low thickness of 45 microns, up to 300 microns or more. The color is dark, the zinc metal is consumed, and the matrix metal is formed into the entry layer, the corrosion resistance is good, and the outdoor environment of hot dip galvanized can adhere to decades.
Did not do the adhesion test of powder spraying or fluorocarbon spray on the packaging galvanized wire, but there are two points for reference: one, in the sealed or air circulation environment, non-metallic volatiles can corrosion zinc coating; Second, zinc above 230 degrees (c) will brittle the base metal. After powder spraying and fluorocarbon spraying, it is necessary to bake at a higher temperature and in a sealed environment, causing rapid corrosion of zinc, resulting in loose corrosion film resulting in decreased adhesion of coating, and even leading to brittle situation of steel wire.
The prepared black wire welding net is placed in environmental protection galvanized equipment for galvanized treatment. The surface of galvanized welding net is evenly covered with a layer of metal zinc. The corrosion resistance of zinc is very good and it is not easy to be oxidized. The wire diameter error of galvanized welding mesh is very strict, and the gap should be controlled at about 0.02 mm. But whether the tension of an electric welding mesh is qualified, can only be tested by professional tools.
If the coating roughness is not caused by the above reasons, it may be caused by impurities in the plating solution. Can take a small amount of electroplating solution, after filtration test, then take a small amount of electroplating solution, after zinc powder treatment test, check the problem is caused by solid particles or copper, lead and other foreign metal impurities. Test them one by one and it’s not hard to find the cause of the problem. Galvanized iron wire coating foaming, binding force is not good.
2, hot plating wire plating after processing
Now hexagonal net is used in a large number of Bridges, piers and bridge buttress inclined plane protection, bridge buttress inclined plane there are many kinds, people according to the inclination of the inclined plane to choose the right hexagonal net, when the inclined plane gentle, people generally use gabion slope protection system, and in the case of steep slope, people will use gabion mesh gravity protection wall.
Galvanized iron wire has good anti-corrosion and anti-rust ability, so it can be used in some outdoor guardrails or fences, especially on handicrafts, which are also of great use. Galvanized iron wire is not easy to rust and oxidation on the surface. Now a lot of hardware manufacturers are producing iron wire, and the iron wire is very easy to rust, if you need to use in outdoor or humid places, the general customer will require the use of galvanized iron wire equipment to give the wire a layer of zinc, the thickness can be determined according to user requirements.When the ground is undulating, the installation method of barbed rope also needs to be changed accordingly, because the installation of the original installation method will not play a protective effect.
Hexagonal mesh is a metal wire woven Angle mesh (hexagonal) made of wire mesh, the use of metal wire diameter is based on the size of the hexagonal and different. Also known as: twist flower net, stone cage net, gabion net, flood control network.
At present, there are two processing methods of blade stabbing rope. One is to make it into a spiral shape, and then make a clip treatment. It is not only our common spiral blade stabbing rope, but also a single spiral blade stabbing rope without clip, but even a single helix can not stretch it to a relatively straight. This is mainly because the blade barbed rope is wrapped and wound at the same time, so it can only be spiral.