The distance between the adjacent two thorn rope installation do not know whether you have noticed? Careful observation can find that its spacing is not the same, the thorn rope factory for customer consultation when asking the installation height of the reason.
The coating of electrode plays a very important role in the welding process. If adopting the light of the coated electrode welding, is in the process of welding, oxygen and nitrogen in the air can invade the molten metal, the metal iron and beneficial elements carbon, silicon, manganese oxide and nitride oxide and nitride formation, and remain in the weld, weld slag or crack. And melt into the molten pool in the gas can make the weld produces a large number of pores, these factors can make the mechanical properties of the weld is greatly reduced, at the same time to make the weld brittle.Stainless steel barbed rope according to the different categories of nickel applications are not the same, in the dry indoor environment using 304 stainless steel effect is quite good. However, in both rural and urban areas, to maintain its appearance outdoors, it is necessary to stop washing frequently. In heavily polluted industrial areas and coastal areas, the surface will be so dirty that it will rust. But to achieve aesthetic effect in outdoor environment, it is necessary to use nickel stainless steel. Therefore, 304 stainless steel is commonly used for curtain wall, side wall, roof and other building uses, but in the corrosive industrial or Marine atmosphere, it is best to use 316 stainless steel.
The vertical distance between the lower edge of the Nestor roller cage and the upper edge of the reinforced concrete protective fence is 0.05m. Longitudinal reinforcement adopts hot-dip galvanized netting, double-twist weaving process, barbed wire 2.2mm, main line 2.5mm, netting joint card adopts galvanized steel plate stamping or Q235 carbon steel plate stamping for galvanized.
Blade barbed rope is a new product of safety protection supplies, and other barbed rope is different with very sharp blade, its production process is the stainless steel sheet stamping forming. The blade barbed wire protective net is a new kind of protective net. The blade barbed wire produced by our factory is made of corrosion-resistant hot-dip galvanized steel plate or stainless steel plate.
With the improvement of people’s living standards, many families are raising some small pets, which also need a stable nest. Pet carrier has become a more important item in people’s choice, and each pet’s different habits and living habits will choose the cage suitable for it.
Breeding cattle and sheep with barbed rope effect is better, because the advantages of more barbed rope. So is the thorn rope used to do animal husbandry good?
Heavy duty hexagonal mesh made of steel wire by special machinery woven into a hexagonal mesh net. This kind of mesh can be cut and assembled into fence mesh, mountain hanging mesh, vegetation three-dimensional mesh, composite, etc. Aliases: Gabion mesh, heavy hexagonal mesh, ecological mesh, wire mesh, etc.
The technical term “galvanized” means that metal has been specially treated with zinc. Essentially, the wire is covered with a very thin layer of zinc. It is this thin layer of zinc that gives galvanized wire its many properties. Galvanizing can be done by dipping wire into a pool of zinc or by electroplating.
When the large roll galvanized wire galvanizing process coating foaming, first check the bath temperature. If the bath temperature is not low, then strengthen the plating before removing oil, prevent the matrix metal in acid corrosion. If you pay attention to these problems, the foaming phenomenon still exists, it should pay attention to the amount and quality of additives, then you can stop adding additives, with high current electrolysis for a period of time, in order to reduce the content of additives, observe whether the foaming phenomenon is improved. If there is still no improvement, it is necessary to check whether the storage period of additives is too long, or whether there are too many impurities in the additives.
The error of construction welding net diameter should be controlled at 0.02 mm. For example, we buy wire diameter of 89 wire welding net, with a micrometer to measure the diameter, the diameter of the allowable range is 87 -91 wire. In this range is qualified welding net. Because the accuracy has been compared, but no one can control it so well in the production process. The welding net can be accurate to 0.01 mm, so the error is allowed.